Farm Irrigation Submersible Sewage Pump Centrifugal Effluent 460 Voltage
| Place of Origin: | Zhejiang |
|---|
Company Profile
| Location: | Shanghai, China (Mainland) |
|---|---|
| Business Type: | Manufacturer |
Product Detail
| Model No.: | CP |
|---|
Product Description
Farm Irrigation Submersible Sewage Pump Centrifugal Effluent 460 Voltage
Application:
| 1 | Farm irrigation . |
| 2 | Pasturage drainage. |
| 3 | Waste water drainage. |
Features:
| 1 | Built-in leakage detector in the oil chamber can dectet leakage from the damage of the mechanical seal. |
| 2 | The power lower than 15KW is optional,not lower than 15KW is standard accessories. |
| 3 | Built-in leakage detector in the wiring box can check if a leak in it |
| 4 | Built-in heat protector in motor, it secures the protection of motor against burning out. |
| 5 | The power lower than 15KW is optional,not lower than 15KW is standard accessories. |
Points for attention before starting equipment:
Warning:The water pump shall not be moved without putting off the power source. Humans shall not contact the water source where the pump is located when pumping water to prevent electric shock accidents in case there is no current leakage protective device while there is current leakage with the pump.
-
Check the insulation condition of the stator winding with a 0-500V meter before starting the water pumps.
-
Check whether the power and the voltage frequency used are in line with those listed on the label.
-
Don't connect the electric wire of the water pump with the power source without any protective device (which may lead to the burning of the motor due to open-phase and overload). Refer to the connection method of the submersible pump. (refer to Page 9 for details).
-
Submerging cable sockets of the motor into water is prohibited.
-
Lifting and hanging the motor with the motor cable is prohibited during the transport and installation processes.
Read this Installation, Operation and Maintenance Manual carefully to guarantee the safe operation of the equipment.
Construction:
| No. | Name | Material | |
| GB | JIS | ||
| 1 | Neck bolt | 2Cr13 | SUS420 |
| 2 | Heat-Protector | - | - |
| 3 | Motor cover | HT200 | FC200 |
| 4-1 | Bearing | - | - |
| 4-2 | Bearing | - | - |
| 5 | Cooling house flange | Q215A | LSS330 |
| 6 | Shaft | 2Cr13 | SUS420 |
| 7 | Rotor | - | - |
| 8 | Stator | - | - |
| 9 | Cooling house | 0Cr18Ni9 | SUS304 |
| 10 | Bearing cover | HT200 | FC200 |
| 11 | Motor casing | HT200 | FC200 |
| 12 | Bracket | HT200 | FC200 |
| 13 | Leakage detector | - | - |
| 14-1 | Mechanical seal | C-Al2O3 | C-Al2O3 |
| 14-2 | Mechanical seal | SiC-SiC | SiC-SiC |
| 15 | Oil box | HT200 | FC200 |
| 16 | Oil cover | HT200 | FC200 |
| 17 | Washer | 0Cr18Ni9 | SUS304 |
| 18 | Impeller nut | HT200 | FC200 |
| 19 | Seal-ring | LBC2 | LBC2 |
| 20 | Strainer | HT200 | FC200 |
| 21 | Impeller | HT200 | FC200 |
| 22 | Pump casing | HT200 | FC200 |
| 23 | Bottom cover |
| |