buy 6200 series deep groove ball bearing 6204 used as idler roller bearing from china bearing supplier

Integrity promise Connaught, intentions to do everything.

Export manufacturer

Passed Certifications - ISO9001:2015

TN Product tested by National Coal Science Institute and Provincial Quality Inspection Center

Except for the basic model, the deep groove ball bearing has some other structures, such as the deep groove ball bearing with dust cap, that of with fibre sealed ring, double row deep groove ball bearing, and so on.

The standard deep-groove, or Conrad, ball bearing is the most simple from the standpoint of design and construction. At the same time, it has the greatest all-around use. Although it is primarily a radial bearing, it is capable of handling moderate thrust loads from either direction and operating at relatively high speeds.

We are a manufacture specialized in producing conveyor roller bearing. bearings also have a clearance value. This provides the bearing room for expansion between the bearing races and will add a small amount of play between the two rings. large clearance C3/C4 usually used in mining machine.

Application

Mining machine, conveyor machine,  Engineering Machinery,  Agricultural Machinery, Construction Machinery, textile, chemical, auto motor, Transportation Vehicles, General industrial Equipment, etc.

Catalog of Deep groove ball bearing

Professional brings quality, detail creates success

XKTE bearing's most fundamental difference is:

The other manufacturers make products considering the price cheap, but we make products considering the service life. Each of the idler roller bearings we produce is fully implemented in the national standard. XKTE bearings exist for their quality and brand. You can deny our price, but you can never find out our products' defects in quality. XKTE conveying machinery bearing, a big brand, is worthy of your trust.

First, the identification of the bearing

Formal manufacturers use laser engraving. The stamps are deep, have significant dents with hand touch, good-looking, with no breakpoints, and are never disappeared. This obviously improves the bearing grade. 

The use of bearing retainer

Bearing retainer selection is very important. Because once too much dust stuck into the bearing, the retainer will be first worn. If the bearing retainer is broken, the bearing will be directly broken. Imported bearings use big rivets to thicken retainers. XKTE bearing is completely in accordance with the process of imported production, so each piece of ours is made to a high quality, and guaranteed to operate for thirty thousand hours.

Selection of nylon retainer

Nylon retainer bearing is often used in the mine. Nylon retainer has better anti-stuck performance and wider range of temperature than iron retainer. In the underground its anti-static performance is also better. To get safety certificate for coal mining products must use nylon retainer KA bearing. The selection of nylon retainer is crucial to KA idler roller bearing, while the material of nylon retainer must be pure and has enough toughness and strength, because the retainer will get very soft if it is made of bad material or mixed material, thus to make no anti-stuck performance within the bearing.

The ring is the main part and the important part of the idler roller bearing. Best idler roller bearing has deep groove ball, and large clearance. But deep groove doesn't mean to dig the channel with a simple way of enlarge the steel ball. The thickness of the bearing is certain, so to get the ball big and the groove deep will shorten service life. Our XKTE bearing uses way of thickening ring to get the standard of deep groove and large clearance, improves the anti-stuck performance, and effectively increases the service life. 

Bearing material and hardness

Good idler roller bearing must be made of bearing steel, named "High Carbon Chromium Bearing Steel (Fully quenched class) GCr15". At present the standard hardness of idler roller bearing is 60-65 degree, while hardness of ring is 61-62 degree, andball is 64-65 degree.

The simple way to identify idler roller bearing is to see if its hardness is over 60 degree, because only bearing steel can get over this degree.

Grease selection of roller bearing

Many customers ignore this most critical point. The thirty-thousands-hours operation is a very long term. This has to be guaranteed by enough quality and quantity grease. And this should also be taken into account of working in different seasons.

Special note: please choose special high temperature grease if working environment is over 120 °C for long time or low temperature grease if it below -20 °C.

Reference:

The key points of idler roller accessories installation

Must remember the key points of idler roller accessories installation. The idler roller accessories are effective in order to play its own value. Idler roller accessories SKF bearing during cooling in the width direction has also contracted, so the installation should apply some pressure to the inner shoulder pressing, and after cooling with thin feeler test for detection, whether there is a gap between the inner ring end face and bearing shoulder. Found to achieve the required heating temperature, it should be installed as soon as possible, so as to avoid cooling and installation difficulties. The heating temperature should be controlled, high temperature of SKF bearing damage, the temperature is too low then ring expansion is insufficient, the effect is not significant. The thermal expansion of the inner diameter of the inner diameter of the inner ring, which is obtained from the temperature in the small control, 1000 to 80 degrees Celsius, is sufficient for the SKF bearing with a general surplus amount.

The impact to the idler roller caused by external environment on accessories is great, according to the actual choice of the appropriate idler roller accessories; according to the production of idler roller to choose the appropriate idler roller accessories. Such as nylon idler roller, the application of what kind of accessories, as well as rubber idler roller should choose what kind of accessories; production process is the choice of accessories should be noted in a large area.

Other Products

Package:

1. Industrial packaging : Single box + outer carton + pallets 

2. Neutral Packing:

Tube package + outer carton + pallets 
Tube package + middle box + outer carton + pallets 

3. As buyer's request

Payment methods:

1) TT, 30% deposit , 70% before shippment.

2) L/C at sight. (high bank charge, not suggest , but acceptable )

3) 100% Western Union in advance. (specially for air shipment or small amount)

Started 2006, We are a manufacture of industrial Bearing in Liaocheng Shandong, concentrates on manufacturing industrial bearing, mainly used in conveying equipment, machinery, textile, chemical, auto motor and so on. Especially bearing for conveyor, which make us become one of well-known enterprise in China. We have 26 production lines, mainly produce deep groove ball bearing, spherical roller bearing, TN Nylon cage bearing and sealed bearing.

All of Our products are made of Chrome Steel GCr15, with grinding groove and superfinishing technology. Supply ability is about 20000 Pieces / per Day. We have our own brand XKTE, and we can also provide OEM service.

FAQ:

I couldn't find a design to fit my application in your catalog. Can you help me design a bearing?

Yes, technical expertise is available to assist you with engineering design for custom products. Available options include, but are not limited to, custom rings, retainers, balls, shields, lubricants, and packaging. We look forward to working with you to satisfy your rotary motion requirements.

What causes bearing noise?

Bearing noise is a function of both the bearing and the way it is used. Some external factors that affect bearing noise include lubricant type, excessive bearing load, and improper installation. Once the abnormal noise occurred, you can contact our engineers, we will help you find the reasons and provide the appropriate solutions.

What is the difference between using a shield or a seal as a ball bearing closure?

Shields or seals are often installed to retain lubricant and to prevent contamination from entering the bearing. While a shield contacts the outer ring and does not come in contact with the inner ring, the seal generally comes in contact with both the inner and outer rings. Torque or drag is lower with a shield than with a seal. Alternately, the seal provides a higher degree of protection from contamination. Shields and seals are available in a variety of materials and configurations.

XKTE developed a serious of sealing methods for different applications. Please contact a XKTE engineer for technical assistance with any special requirements.

Our Advantage

1. Excellent and high quality control

2. Prompt delivery

3. Long life and low noisy

3. Competitive price and with avalible samples

4. Small order accepted

5. Customers' drawing or samples accepted

6. OEM service

86-15688862750

02 at xinkaite.com

www dot xinkaite dot com