Hypertehrm Accessories Shield 220338 Hyperther Cutter consumables For HPR130XD Machine
FAQ:
Q1:Can I get a free samples to check the quality?
A:Sure,we can supply the free samples but you need bear the express cost by yourself.
Q2:Will I afford the carrier charge?
A:Yes,you will afford the express charge or your account is OK.
Q3:Can I add my trademark on my products?
A:Yes,we need your certificate of authorization.
Feedback
1.Since your feedback is very important to our business's development, we sincerely invite you to leave positive feedback for us if
you are satisfied with our product and service. It'll just take you 1 minute.
2.Please contact us before leaving any negative or neutral feedback. We will work with you to solve any problems.Thank you!
Each of our products has been tested with a rigorous precision instrument, A large number of piercings tests and service life tests, And made batch trial in our customers. If all results are good, then we will producing them.
| Machine |
HEC NO. |
Ref NO. |
Description |
|
HPR 130
HPR 260
HPR 130XD
HPR 260XD
HPR 400XD
|
H03192 |
220192 |
Electrode,30Amp |
| H03552 |
220552 |
Electrode,50Amp |
| H03187 |
220187 |
Electrode,80Amp |
| H03181 |
220181 |
Electrode,130Amp |
| H03352 |
220352 |
Electrode,200Amp |
| H03435 |
220435 |
Electrode,260Amp |
| H03649 |
220649 |
Electrode,130Amp Bevel |
| H03541 |
220541 |
Electrode,260Amp Bevel |
| H03665 |
220665 |
Electrode,130Amp(silver Plus) |
| H03666 |
220666 |
Electrode,200Amp(silver Plus) |
| H03668 |
220668 |
Electrode,260Amp(silver Plus) |
| H03629 |
220629 |
Electrode,400Amp |
| H73180 |
220180 |
Swirl Ring,30Amp |
| H73553 |
220553 |
Swirl Ring,50Amp |
| H73353 |
220353 |
Swirl Ring,200Amp |
| H73179 |
220179 |
Swirl Ring,80/130/260Amp(Bevel) |
| H73436 |
220436 |
Swirl Ring,260/260Amp(Bevel) |
| H73631 |
220631 |
Swirl Ring,400/400Amp(Bevel) |
| H13193 |
220193 |
Nozzle,30Amp |
| H13554 |
220554 |
Nozzle,50Amp |
| H13188 |
220188 |
Nozzle,80Amp |
| H13182 |
220182 |
Nozzle,130Amp |
| H13354 |
220354 |
Nozzle,200Amp |
| H13439 |
220439 |
Nozzle,260Amp |
| H13646 |
220646 |
Nozzle,130Amp(Bevel) |
| H13542 |
220542 |
Nozzle,260Amp(Bevel) |
| H13632 |
220632 |
Nozzle,400/400Amp(Bevel) |
| H33754 |
220754 |
Retaining Cap 30/50Amp |
| H33176 |
220176 |
Retaining Cap 80/130Amp |
| H33355 |
220355 |
Retaining Cap 200Amp |
| H33433 |
220433 |
Retaining Cap 260Amp |
| H33603 |
220603 |
Retaining Cap (Bevel) 130/260Amp |
| H33756 |
220756 |
Retaining Cap 80/130Amp |
| H33757 |
220757 |
Retaining Cap 200Amp |
| H33760 |
220760 |
Retaining Cap 260Amp |
| H33635 |
220635 |
Retaining Cap 400/400Amp(Bevel) |
| H33740 |
220740 |
Retaining Cap (Bevel) 130/260Amp |
| H23194 |
220194 |
Shield,30Amp |
| H23555 |
220555 |
Shield,50Amp |
| H23189 |
220189 |
Shield,80Amp |
| H23183 |
220183 |
Shield,130Amp |
| H23356 |
220356 |
Shield,200Amp |
| H23440 |
220440 |
Shield,260Amp |
| H23645 |
220645 |
Shield,130Amp(Bevel) |
| H23545 |
220545 |
Shield,260Amp(Bevel) |
| H23761 |
220761 |
Shield,200Amp |
| H23764 |
220764 |
Shield,260Amp |
| H23636 |
220636 |
Shield,400/400Amp(Bevel) |
| H23742 |
220742 |
Shield,130Amp(Bevel) |
| H23741 |
220741 |
Shield,260Amp(Bevel) |
| H43173 |
220173 |
Retaining Cap 30/50/80/130Amp |
| H43398 |
220398 |
Retaining Cap 200/260/(Bevel)130/260Amp |
| H43747 |
220747 |
Retaining Cap 30/50/80/130Amp |
| H43637 |
220637 |
Retaining Cap 200/260/400Amp(Bevel) |
| H83818 |
128818 |
HPR torch assembly |
| H83162 |
220162 |
Quick-disconnect torch |
| H83163 |
220163 |
Quick-disconnect recepticle |
| H83706 |
220706 |
Quick-disconnect torch |
| H83705 |
220705 |
Quick-disconnect recepticle |
| H93571 |
220571 |
Water Tube with O-Ring |
| H93340 |
220340 |
Water Tube with O-Ring(30/50/80/130/200/260Amp) |
| H93700 |
220700 |
Bevel water tube(mild steel-130A) |
Technical Support:
Method for prolonging the service life of the plasma wearing parts
1 ensure the correct air pressure and flow rate of the plasma gas
The correct pressure and flow rate of the plasma gas are very important to the service life of the wearing parts. If the pressure is too high, the life of the electrode will be greatly reduced; If the pressure is too low, the nozzle's life will be affected, using a reasonable cut distance: In accordance with the requirements of the use of the specification, the use of a reasonable cut (cutting the distance between the nozzle and the working surface), when the perforation, the initial arcing distance as far as possible The maximum height of the plasma arc can be transferred by 2 times of normal cutting distance. the thickness of the perforation should be within the scope of the plasma system. Cutting machine can not be perforated over the thickness of the plate, usually the thickness of the normal thickness of the thickness of the cutting 1/2. For example: the 100A plasma system for cutting 1 inches (about 25mm) of carbon steel, the system perforation thickness should be 0.5 inches (about 12.5mm). nozzles do not overload, Let the nozzle overload (that is, over the working current of the nozzle), the nozzle will soon be damaged. The current intensity should be 95% of the working current of the nozzle. For example: 100 the current intensity of the nozzle should be set to 80--60A. keep the drying and cleaning of the plasma gas. Plasma system need to dry clean plasma gas to work properly, gas compression system often pollute the gas, so easy to shorten the service life of wearing parts, resulting in damage to the non normal damage. The quality of test gas method is the system in state test, a mirror is placed at the bottom of the torch, torch vent gas, such as on the mirror produces water vapor or
