Stone Glue Sandstone Tile Adhesive / Strong Adhesive Strength
| Place of Origin: | Zhejiang |
|---|
Company Profile
| Location: | Guangzhou, Guangdong, China (Mainland) |
|---|---|
| Business Type: | Manufacturer |
| Main Products: | Ceramic Wall Tile Adhesive |
Product Detail
| Model No.: | PB-03 |
|---|
Product Description
Stone Glue Sandstone Tile Adhesive / Strong Adhesive Strength
PB-03 is a kind of high quality environment-friendly waterborne powder which can be mixed with water and used for bonding ceramic tile on the surfaces of wall, ground and floor. It is easily applied and can achieve an excellent adhesion.
Product Description
Product features:
1. Has strong cohesion force. Reduce the common phenomenon of tiles detaching and peeling when pasted by Portland cement.
2. Be premixed and produced, the product is stable, water and used, to protect the construction environment.
3. Has strong water retention, no need to DIP tiles and wet walls, thin construction, easy operation, to reduce material consumption and building load.
4. Has good flexibility to resist effectively the destruction of various stresses.
5. Has special formula to avoid completely the common phenomenon of tiles cracking, detaching and peeling by Portland cement.
6. It is no-toxic, no-radiation, no smell and environmental.
7. Has special formula to prevent the flow with too much southbound crash, easier construction.
Treatment of base plane:
1. Base plane should be smooth and firm, no dust, grease, release agents, batik material, etc.
2. Check base plane roughness by 2m guiding rule, error should be less than 5mm.
3. New plastering cement mortar could be constructed after 14 days maintenances.
Construction technology:
1. Construction tools: Leveling instrument, dentiform drawknife (3×3mm, 4×4mm, 6×6mm, 8× 8mm, 10×10mm), tile generator, motor stirrer, big drum, cross-colloidal.
2. Stir and mix: Mix tile adhesive and water as 20: (5~5.5) stirs completely and waiting for 5 minutes, stir again.
3. Layup construction: Scrape the glue paste evenly on base plane with dentiform drawknife, the area should be about 1 m ² each time, then knead and press on the base plane. The model of the dentiform drawknife depends on the size of the tiles.
Attentions:
1. The vertical and smoothness of the substrate must be confirmed before construction.
2. The product is suitable for construction in the 5~40.
3. Don't use the dried paste by reading water.
4. If the base plane is uneven or the back of tile is not smooth, wiping the paste on the back of brick in order to ensure it full with paste to avoid hollowing.
Technical parameters:
| Original tensile adhesive strength(Mpa) | ≥1.0 | |||
| Tensile adhesive strength after water(Mpa) | ≥1.0 | |||
| Tensile adhesive strength after thermal aging(Mpa) | ≥1.0 | |||
| Tensile adhesive strength after thawing cycle(Mpa) | ≥1.0 | |||
| Tensile adhesive strength after standing for 20 min(Mpa) | ≥1.0 | |||
Use level list |
| ||||
Tile size | Drawknife size | Use level(kg/sqm) |
| ||
10×10cm tile or mosaic or below | 6×6mm tooth form for base. | 3~4 |
| ||
60×60cm tile and stone or below | 8×8mm tooth form for base. | 4.5~6 |
| ||
60×60cm tile and stone or above | 10×10mm tooth form for base. | 6~8 |
| ||
60×60cm tile and stone or below, with deep groove | 8×8mm tooth form for base. | 6~8 |
| ||
60×60cm tile and stone or above, with deep groove | 10×10mm tooth form for base. | 8~12 | |||