APR Downhole Tester Valve without lock-open Mode DST Tools
| Min. Order: | 1 Set/Sets |
|---|---|
| Trade Term: | FOB,CFR |
| Payment Terms: | L/C, T/T |
| Supply Ability: | 10sets/month |
| Place of Origin: | Shaanxi |
Company Profile
| Location: | Xi'an, Shaanxi, China (Mainland) |
|---|---|
| Business Type: | Manufacturer, Distributor/Wholesaler, Service |
Product Detail
| Model No.: | LPR - N valve |
|---|---|
| Means of Transport: | Ocean, Air, Land |
| Working pressure: | 105Mpa |
| Working Temperature: | 400F |
| Material: | AISI4140 |
| Type: | Full bore |
| Use: | Downhole tester |
| Condition: | NEW |
| Standard: | Nace MR0175/ISO |
| Size: | 5" |
| Application: | Drill stem testing |
| Delivery: | 30 days |
| Production Capacity: | 10sets/month |
| Packing: | plywood |
| Delivery Date: | 35days |
Product Description
APR Downhole Tester Valve without lock-open Mode DST Tools
Downhole Tester Valve without lock open mode LPR-N Valve
The LPR-N Tester Valve is a full-opening, annulus pressure-operated valve. It permits measuring multiple closed-in
pressures in cased holes where pipe manipulation is restricted and a full-opening string is required.The nitrogen
chamber is charged at the surface to a selected pressure determined by surface temperature and bottomhole
temperature and pressure. As the LPR-N Tester Valve is run into the well, the ball valve can either set up to be in the
open or closed position. The power section controls the ball valve mechanism. The power section has a moving piston
with one side exposed to hydrostatic pressure and the other side exposed to pressurized nitrogen. After the packer has
been set, pressure is applied to the annulus, moving the piston downward to pull the ball into the open position.
Releasing annulus pressure allows the pressurized nitrogen to return the piston upward to close the ball valve.
The nitrogen chamber is charged at the surface to a predetermined pressure depending upon surface temperature,
bottomhole temperature, and hydrostatic pressure at testing depth. This charging pressure gives the tool the optimum
volume for compression in the nitrogen chamber when the tool arrives at testing depth. These values do not have to be
exact because the floating piston compensates for small inaccuracies Annulus pressure is transmitted to the nitrogen
chamber through the oil chamber and metering cartridge. As the tool is run in the hole, pressure enters
the tool through the lower annulus ports below the oil chamber. When the tool reaches the desired testing depth, there
will be less pressure in the nitrogen chamber than in the annulus. This creates a pressure differential across the
operating piston, which is acting to open the ball valve. For this reason, shear pins are needed to keep the ball valve in
the closed position until ready to test. The shear pins in the 5-in. tool have an approximate rating of 280 psi/pin.
Normally the tool is set up with four pins. To close the ball valve, the annulus pressure is released at a safe maximum
rate. This creates a differential across the operating piston due to the stored pressure in the nitrogen chamber. The
differential pressure moves the operating piston upward, rotating the ball to the closed position. After approximately
10 minutes, the nitrogen pressure has dropped to a level slightly higher than annulus hydrostatic, helping keep the ball
in the closed position.
Specification:
| Specifications | 5" | ||||
| OD | 127.5mm | ||||
| ID | 57mm | ||||
| Length | 4940mm(3 1/2"IF BXP) | ||||
| Working Pressure | 105Mpa | ||||
| Diff. pressure over ball valve | 70Mpa | ||||
| Diff. pressure to Ball valve open | 35Mpa | ||||
| Internal Yield Pressure strength(Bursting pressure) | 140Mpa | ||||
| External Yield Pressure strength (Collapse Pressure) | 130Mpa | ||||
| Tensile Strength(Yield) | 1947KN | ||||
| Torque Strength | 61KN.m | ||||
| Service environment | Mud, Crude Oil, Natural gas NACE MR0175(>175F) | ||||
| Service temperature | --29oC~+204oC | ||||
| End connections | 3 7/8 CAS, 3 1/2" IF | ||||
ZZ TOP OIL TOOLS is the professional manufacturer for the drill stem testing tools and surface testing equipment. All the DST tools are
conformed with NACE MR 0175 with traceability,and the DST tools can be worked in H2S & CO2 above 175 F and full H2S, also with the skilled
and experienced engineers, we can design the drill stem testing tools as per customer's well condition. Moreover, we supply the training in
our factory and operation instruction at the well site. The DST tools are exported to USA, Colombia, India, Pakistan, Iran, Brazil etc. and
enjoy the good reputation from the customers.
To shorten the delivery time, we proceeded the DST Tools in stock:
Packer,circualting valve,select tester valve,APR N-valve,OMNI valve,Hydraulic Jar,Tubing string tester
1. Full bore Packer, 7" Casing, working pressure 70Mpa, Working Temperature 400F, Connection: IF, 4set
2. Tester valve, 5", Working pressure 105Mpa, Working temperature 400F, Connection CAS. BXP, 4 sets
3. Hydraulic Jar,5", Working pressure 105Mpa, Working temperature 400F, Connection CAS. BXP, 4sets
4. Rupture disk Circulating valve, 5", Working pressure 105Mpa, Working temperature 400F, Connection CAS. BXP, 4sets
5. Flowhead (surface test tree), 3 1/16", working pressure 70 Mpa. 1set
Should you have any interest or inquiry on the Drill stem testing tools, contact us freely.
APR Downhole Tester Valve without lock-open Mode DST Tools
Downhole Tester Valve without lock open mode LPR-N Valve