25w 12V to 24V Converter SD-25A-24
Features:
2:1 wide input range
Protections: Short circuit / Over load / Over voltage
1500VDC I/O isolation
Built-in EMI filter, low ripple noise
100% full load burn-in test
Fixed switching frequency at 83 KHz
Low cost
High reliability
1 year warranty
25W 12V to 24V Converter SD-25A-24 SpecificationMODEL | SD-25A-24 |
OUTPUT | DC VOLTAGE | 24V |
RATED CURRENT | 1.1A |
CURRENT RANGE | 0 ~ 1.1A |
RATED POWER | 26.4W |
RIPPLE & NOISE (max.) Note.2 | 150mVp-p |
VOLTAGE ADJ. RANGE | 23 ~ 30VDC |
VOLTAGE TOLERANCE Note.3 | ±1.0% |
LINE REGULATION | ±0.2% |
LOAD REGULATION | ±0.2% |
SETUP, RISE, HOLD TIME | 2.5s, 50ms, --- at full load |
INPUT | VOLTAGE RANGE | 9.2 ~ 18VDC |
EFFICIENCY (Typ.) | 75% |
DC CURRENT | 0.8A/48V |
PROTECTION | OVERLOAD | 105 ~ 150% rated output power |
Protection type : Fold back current limiting, recovers automatically afterfault condition is removed |
OVER VOLTAGE | 31.5 ~ 37.5V/10% load |
Protection type: Hiccup mode, recovers automatically after fault conditionis removed |
ENVIRONMENT | WORKING TEMP. | -10 ~ +60ºC |
WORKING HUMIDITY | 20 ~ 90% RH non-condensing |
STORAGE TEMP., HUMIDITY | -20 ~ +85ºC, 10 ~ 95% RH |
TEMP. COEFFICIENT | ±0.03%/ºC (0 ~ 50ºC) |
VIBRATION | 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes |
SAFETY & EMC (Note 4) | SAFETY STANDARDS | Design refer to LVD |
WITHSTAND VOLTAGE | I/P-O/P:1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC |
ISOLATION RESISTANCE | I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC |
EMI CONDUCTION & RADIATION | Design refer to EN55022(CISPR22) CLASS B |
EMS IMMUNITY | Design refer to EN61000-4-2,3,4,6,8;ENV50204,EN55024,light industry level,criteria A |
OTHERS | MTBF | 374.3K hrs min. MIL-HDBK-217F (25ºC ) |
DIMENSION | 99*97*36mm (L*W*H) |
PACKING | 0.38Kg; 45pcs/17.8Kg/0.9CUFT |
NOTE | 1. All parameters NOT specially mentioned are measured atnormal input, rated load and 25ºC of ambient temperature. 2. Ripple &noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wireterminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance: includesset up tolerance, line regulation and load regulation. 4. The power supply isconsidered a component which will be installed into final equipment. The finalequipment must be re-confirmed that it still meets EMC directives. |
25W 12V to 24V Converter SD-25A-24 Mechanical Specification:
25W 12V to 24V Converter SD-25A-24 Certificate for LVD:
SD-25A-24 Certificate for EMC: